Set Your Component Watchlist Now, Not After the Shortage

Image
Pulse
Adam J. Fleischer
Adam J. Fleischer
Nov 18, 2026

With three designs headed for BOM freeze in the first quarter of 2027, an electrical engineer runs an availability check for a motor controller, a sensor gateway, and a power supply board revision. All 180 unique parts on the three BOMs show franchised distributor stock, including the high-capacitance MLCCs in the power stage and the DDR4 memory on the gateway. By the usual stock check, all three BOMs look clean.

But the engineer knows today’s stock count doesn’t guarantee all those 180 parts will be available in quantity when procurement places orders for the first production runs in mid-2027. To reduce the risk of a shortage after the freeze, the engineer builds a component watchlist for the parts most likely to tighten. If a distributor’s stock on one of those parts drops below a chosen level, the engineer gets an email alert and can begin qualifying an alternate before the BOMs are frozen. 

Key Takeaways

  • Stock today can be gone by production. By mid-August 2026, leading manufacturers reportedly ran out of certain high-capacitance MLCCs, with restocking expected between November 2026 and January 2027.
  • Build a short watchlist. Start with parts you can’t easily swap and parts from tight categories; then evaluate stock patterns to decide which other parts to watch.
  • Set below-threshold alerts. With a free Octopart account, you can get an email when a distributor’s stock on a watched part drops below a level you set.
  • Act on the warning early. When an alert arrives before freeze, review current offers and the part’s Inventory history in Octopart to assess whether to buy ahead, begin qualifying an alternate, or both.

A Clean BOM Today Can Still Run Short in 2027

High-capacitance MLCCs, like the ones on the engineer’s power supply board, show how unevenly a common category can tighten. In August 2026, TrendForce reported that lead times for standard-case MLCCs were holding steady at 14 to 18 weeks, while DigiKey data in the same report showed some high-capacitance parts from Samsung Electro-Mechanics stretching to about 40 weeks.

Securities reports cited by TrendForce said that by mid-August, Samsung Electro-Mechanics, Murata, and Yageo had run out of certain high-capacitance MLCCs used in servers and high-performance power supplies, with restocking expected between November 2026 and January 2027. New MLCC capacity planned for late 2026 has also reportedly been pushed into 2027. The memory market has faced similar pressure, as AI data centers pull wafer capacity toward high-bandwidth memory and away from conventional DRAM and NAND.

Restock dates like these are only estimates, and they can slip. If power-stage MLCCs or the gateway’s DDR4 run short after the BOMs are frozen, it can take weeks to evaluate and qualify alternates, and sometimes requires changing the layout. With a watchlist, the engineer can catch parts like these while the BOMs are still open to change.

Choose the Parts Worth Watching

An effective watchlist starts small. Alerts on all 180 parts would bury the useful notices among emails about routine stock fluctuations. The engineer narrows the list in three steps:

1. Start with Hard-to-Swap Parts

The first candidates are parts that would force a design change if they went short. A single-source part, a part with an uncommon footprint or pinout, or a device with a heavy qualification burden – such as the motor controller’s automotive-grade gate driver or the gateway’s certified radio module – rarely has a quick alternate and belongs on the watchlist. A resistor with dozens of stocked equivalents in the same package can stay off the list.

2. Add Parts from Tight Categories

Next, add parts from categories already under supply pressure. On the engineer’s three designs, that includes the high-capacitance MLCCs on the power board and the gateway’s DDR4, even though both are in stock today. For a look into which categories are likely to tighten next year, see Will 2027 Loosen Up? The Category by Category Outlook.

3. Screen Each Candidate with Inventory History

The first two steps turn up 32 candidates. Parts that are hard to swap stay on the list, whatever their stock history. For the rest, including parts from tight categories, check how stock has held up over time. The Inventory history graph (Figure 1) on each Octopart part page shows franchised distributor stock in 3-month and 12-month views. The 12-month view shows patterns that today’s stock count doesn’t show:

  • If stock has held steady well above the build quantity, the part can come off the list.
  • If stock has dropped to near zero and recovered more than once, keep the part on the list.
  • If stock has declined month over month, keep the part on the list and look for alternates now.

Figure 1: The MLCC’s 12-month Inventory history: stock usually runs above 60,000, but it fell close to zero twice before recovering.

After this screening, the list drops from 32 candidates to 15. One of the power-stage MLCCs stays on the list, since its 12-month history shows two dips close to zero. The DDR4 stays on as well, because its stock has declined month over month.

Set Low-Stock Alerts on Parts You Can Still Buy

All 15 parts are in stock today, so each one gets a below-threshold alert. (For parts that are already short, Get Pinged the Moment Your Component Is Back in Stock (available soon) explains how above-threshold alerts email you when supply returns.)

Size the Threshold to One Distributor’s Stock

Take the MLCC that made the list. The power supply board uses 8 of them, so a 1,000-board production run needs 8,000. The part’s Inventory history in Octopart shows franchised stock usually above 60,000.

Octopart checks each alert against an individual distributor’s stock, not the franchised stock total that Inventory history shows, so the threshold has to fit what one distributor carries. The part page lists each distributor’s current stock, and the main distributor for this MLCC shows about 45,000. Inventory history shows today’s total close to its usual level, so the engineer estimates the main distributor’s normal stock at 40,000 or more. If procurement has tracked this distributor’s stock, its numbers give a better estimate. A good threshold is below that range (otherwise routine fluctuations would trigger it) and well above the 8,000 a single production run needs. For this MLCC, the engineer selects 25,000, which meets both criteria. In both past dips (Figure 1), stock took one to three weeks to fall from its usual level to near zero, and that’s the warning window a below-threshold alert is built to catch.

An alert is a prompt to check the part, not a reserve of stock. Other buyers draw from the same distributor stock, and one large order can drop it below 8,000 before procurement places its order.

Create the Alert from the Part Page

With 25,000 decided upon as the MLCC’s threshold, the engineer creates the alert with this simple process:

  1. Sign in to Octopart and search for the MPN.
  2. Open the part page and click Watch (Figure 2).
  3. Choose Below and enter 25,000 as the quantity (Figure 3).
  4. Click Edit to select the distributors to monitor (if you skip this step, Octopart uses your preferred distributors).
  5. Click Save to Watchlist.

Figure 2: Click Watch on the part page to set an alert.

Figure 3: Choose Below, enter the threshold quantity, and select the distributors to monitor.

Pick distributors on your approved vendor list whose current stock is well above the threshold quantity.

Check the Watchlist at Each Design Review

All your alerts can be managed from Octopart’s Watchlist (Figure 4). You can navigate to it by clicking the profile icon at the top right of Octopart, then select Watchlist.  

Figure 4: Octopart’s Watchlist shows each alert’s threshold and each monitored distributor’s current stock. The screenshot shows the MLCC alert and an alert for an STM32G431CBU6 microcontroller.

At each design review, the engineer rechecks each threshold against current build quantities and distributor stock, and removes alerts for parts cut from a design. Each alert emails once, the first time stock crosses its threshold, so after one fires, re-create the alert if the part still needs watching.

Act on an Alert Before the BOM Freeze

After getting an alert before freeze, the engineer opens the part page, compares current distributor offers, looks at the part’s 12-month Inventory history, and asks procurement to confirm available stock and replenishment dates with the distributor. 

If past dips on this part recovered quickly and the confirmed replenishment dates fit the build schedule, an early purchase may be all that’s needed. If stock has declined for months, as with the gateway’s DDR4, the engineer starts qualifying an alternate while procurement checks whether an advance purchase can cover near-term needs.

For alternates, the Similar Parts section of the part page lists comparable parts matched on key specifications. The team checks each one for electrical specs, footprint compatibility, and qualification requirements. When supporting both parts requires a layout change, the team makes and validates that change before freeze. Once an alternate passes qualification, the team can add it to the BOM.

At freeze, the engineer sends procurement the list of watched parts (including why each one is on it), and procurement can set its own alerts at final production quantities. For a procurement-focused view on these decisions, see Building a Supply Risk Plan That Survives 2027.

180 Clean-Looking Parts, 15 Real Risks

The engineer started with 180 parts that all looked clean and ended with 15 alerts, each on a part that would be hard to swap or whose stock history showed supply pressure. If the MLCC’s main distributor drops below 25,000 before freeze, the team can find out with time left to buy ahead or qualify an alternate.

Start by Watching 3 to 5 Parts

To get familiar with watchlist alerts, start with a small list. Pick three to five hard-to-swap parts from your design closest to freeze, size each threshold between your build quantity and the main distributor’s current stock, and create the alerts. Then add parts from your other designs before their BOMs are frozen. You’ll sleep better at night after your alerts have been set.

Create a free Octopart account to start your watchlist.

Read More Articles