Analog Devices AD5171BRJZ5-R2

IC DGTL POT 5KOHM 64TAP SOT23-8 / Digital Potentiometer 5k Ohm 1 Circuit 64 Taps I²C Interface SOT-23-8

Digital Potentiometer 64POS 5kOhm Single Automotive 8-Pin SOT-23 T/R

IT CAN ALSO OPERATE FROM A 5V NOMINAL SUPPLY AD5171 Gold Selectable Address digital potentiometer 1.5kHz 3/5V 5kOhm 1.3mm

DIGITAL POT, 5KOHM, SINGLE, SOT-23-8; End To End Resistance:5kohm; No. of Pots:Single; Control Interface:I2C; Track Taper:Logarithmic; Resistance Tolerance:± 30%; Supply Voltage Min:2.7V; Supply Voltage Max:5.5V; No. of Pins:8Pins RoHS Compliant: Yes

DIGIPOT 6BIT OTP I2C 5K, SMD, 5171; End To End Resistance:5kohm; Resistance Tolerance:± 30%; No. of Steps:64; Supply Voltage Range:2.7V to 5.5V; Control Interface:Serial, I2C, 2-Wire; No. of Pots:Single; Memory Type:OTP; Temperature Coefficient:± 35ppm/°C; Potentiometer IC Case Style:SOT-23; No. of Pins:8; Operating Temperature Range:-40°C to +125°C; SVHC:No SVHC (19-Dec-2011); Base Number:5171; IC Generic Number:5171; Interface Type:I2C; Logic Function Number:5171; Memory Type:One Time Programmable; No. of Channels:1; No. of Positions:64; Operating Temperature Max:125°C; Operating Temperature Min:-40°C; Package / Case:SOT-23; Resistance Range Type:Linear; Supply Voltage Max:5.5V; Supply Voltage Min:2.7V; Termination Type:SMD; Track Resistance:5kohm

The AD5171 is a 64-position, one-time programmable (OTP) digital potentiometer2 that uses fuse link technology to achieve the memory retention of the resistance setting function. OTP is a cost-effective alternative over the EEMEM approach for users who do not need to reprogram new memory settings in the digital potentiometer. This device performs the same electronic adjustment function as most mechanical trimmers and variable resistors. The AD5171 is programmed using a 2-wire, I2C®-compatible digital control. It allows unlimited adjustments before permanently setting the resistance value. During the OTP activation, a permanent fuse blown command is sent after the final value is determined, freezing the wiper position at a given setting (analogous to placing epoxy on a mechanical trimmer). When this permanent setting is achieved, the value does not change regardless of supply variations or environmental stresses under normal operating conditions. To verify the success of permanent programming, Analog Devices, Inc., patterned the OTP validation such that the fuse status can be discerned from two validation bits in read mode. For applications that program the AD5171 in factories, Analog Devices offers device programming software that operates across Windows® 95 to XP platforms, including Windows NT. This software application effectively replaces the need for external I2C controllers or host processors and, therefore, significantly reduces the development time of the users. An AD5171 evaluation kit includes the software, connector, and cable that can be converted for factory programming applications. The AD5171 is available in a compact 8-lead SOT-23 package. All parts are guaranteed to operate over the automotive temper-ature range of -40°C to +125°C. Besides its unique OTP feature, the AD5171 lends itself well to other general-purpose digital potentiometer applications due to its temperature performance, small form factor, and low cost. Applications System calibrations Electronics level settings Mechanical trimmers and potentiometer replacements Automotive electronics adjustments Gain control and offset adjustments Transducer circuit adjustments Programmable filters up to 1.5 MHz BW1 1Applies to 5 kO parts only. 2 The terms digital potentiometer and RDAC are used interchangeably. Data Sheet, Rev. D, 7/08